Uit Hack42
Ga naar: navigatie, zoeken
 
(Een tussenliggende versie door dezelfde gebruiker niet weergegeven)
Regel 1: Regel 1:
 
{{Project
 
{{Project
 
|Naam=OneWireSwitch
 
|Naam=OneWireSwitch
|Eigenaar=BugBlue,
+
|Eigenaar=BugBlue
|Status=Uitvoer
+
|Status=Afgerond
 
|Skills=solderen, slijpen, zagen, schroeven, programmeren
 
|Skills=solderen, slijpen, zagen, schroeven, programmeren
 
|Samenvatting=Onewire switch bouwen op basis van een oude switch
 
|Samenvatting=Onewire switch bouwen op basis van een oude switch
 
}}
 
}}
 +
== The idea ==
 +
* Take a (broken) 19" switch
 +
* Saw off the exces part of the switch you don't need (everything except the ports and the PCB directly underneath)
 +
* figure out the pins
 +
** Pin 1: ground
 +
** pin 2: data
 +
** pin 3: VCC
 +
* get a rasterized printboard and some headers
 +
* make a shield for your arduino
 +
** Connect all the data pins to the data cables for the ports (16 in this case)
 +
** solder 16 resistors (1k or 4k7) from 5V VCC to all the datapins
 +
** solder 5V and GND
 +
* screw the arduino to the board
 +
* connect the shield to the arduino
 +
* insert a USB cable
 +
* upload the software
 +
* close the case
 +
* apply stickers
 +
* place the switch in the rack
 +
* If any time is left you can connect some leds
 +
 +
== The software ==
 +
<pre>
 +
please type in here...
 +
</pre>
 +
 
== Gezocht ==
 
== Gezocht ==
 
Nyancat stickers. Ter hoogte van 1U :)
 
Nyancat stickers. Ter hoogte van 1U :)

Huidige versie van 19 aug 2012 om 19:07

Project: OneWireSwitch
Schroefje24.png
Schroefje24.png
Schroefje24.png
Schroefje24.png
OneWireSwitch Picture.jpg

OneWireSwitch

Naam OneWireSwitch
Door BugBlue
Status Afgerond
Madskillz solderen, slijpen, zagen, schroeven, programmeren
Doel / Omschrijving
Onewire switch bouwen op basis van een oude switch
Alle Projecten - Project Toevoegen
File:OneWireSwitch_Picture.jpg noez

The idea

  • Take a (broken) 19" switch
  • Saw off the exces part of the switch you don't need (everything except the ports and the PCB directly underneath)
  • figure out the pins
    • Pin 1: ground
    • pin 2: data
    • pin 3: VCC
  • get a rasterized printboard and some headers
  • make a shield for your arduino
    • Connect all the data pins to the data cables for the ports (16 in this case)
    • solder 16 resistors (1k or 4k7) from 5V VCC to all the datapins
    • solder 5V and GND
  • screw the arduino to the board
  • connect the shield to the arduino
  • insert a USB cable
  • upload the software
  • close the case
  • apply stickers
  • place the switch in the rack
  • If any time is left you can connect some leds

The software

please type in here...

Gezocht

Nyancat stickers. Ter hoogte van 1U :)